HOME/Vertical Machining Center/V Series/MCV-1500i+
 
 
  MCV-1100i | MCV-1300 | MCV-1500i | MCV-1500i+ | MCV-2000i
   
 
LEADWELL's mission is to constantly search for excellence and gain respect in the industry. Using our 25 years of experience, the entire staff at LEADWELL pledges to bring innovation, quality assurance, worldclass after sales service, and environmentally friendly machine tools to the worldwide marketplace. We strive to win the respect of both our customers and world wide competitors alike.
   
 
Directly Coupled Servo Motors
The V/MV/MCV-Series servo motors are connected to the ball screws with rigid shaft couplings. These couplings ensure that even under severe loading from sharp corner machining, precise interpolation is achieved. This design is superior to both and flexible shaft coupling designs.
Chip Removal

LEADWELL's simple and efficient design uses chip augers on both sides of the machine and provides high volume coolant to wash the chips from the work area. The augers move the chips into the disposal container, which eliminates the need for an operator to manually remove chips. This system eliminates operation intervention and reduces non-cutting time.
Rigid Tapping

The encoder is directly attached to the high-performance spindle motor. The spindle is then synchronized with the Z-axis motion. This synchronization eliminates the need for expensive floating tap holders and prevents thread distortion and thread pullout.

Double Nut Designed Ball Screws

LEADWELL uses only premium quality preloaded double-nut ball screws. On the V/MV/MCV-Series machines each ball screw is accurately aligned parallel to the guide ways and anchored at both ends. They are then pre-tensioned to improve machine stiffness. The rotational torque variation is inspected to guarantee a non-binding, highly accurate, and long running component. With this design the V/MV/MCV-Series can exceed customer requirements for accuracy and maximum life.
Swivel Operator Panel

The operator panel swivels for better operator convenience.

Cartridge Type Spindle

The heavy-duty spindle utilizes FAG, NSK or SKF bearings to allow heavy cutting. Oversized disk springs used to hold the tool in the spindle are tested for long life. The high retention force of the springs reduce tool movement, improve tool life, allow heavier cutting, reduce chatter, & create a better part finish. This spindle is prepared to easily add the CTS option.
Heavy-Duty Box Ways

  The heavy-duty box ways are hardened to HS67-75 (HRC 50-60) and precision ground. The female box ways and gibs are coated with anti-friction Turcite B. These features help allow the machine to maintain maximum accuracy levels.

Ball Bar Testing

LEADWELL uses a stringent ball bar test that checks not only linear accuracy but also machine geometry. This test insures that each machine meets the three-dimensional squareness and accuracy requirements.
Technical Specifications

Item   Drum type Arm type
X axis travel mm (in) 1520 (59.8) 1520 (59.8)
Y axis travel mm (in) 1000 (40) 1000 (40)
Z axis travel mm (in) 685+160 (27+6.3) 720 (28.3)
Table size (LxW) mm (in) 1550x1000 (61x40) 1550x1000 (61x40)
Spindle speeds rpm 4000 4000
Spindle motor (30min) FANUC kw (HP) 11/15 (14.7/20.1) 11/15 (14.7/20.1)

Accessories: Standard | Optional

 
  • RS232 interface
  • Rigid tapping
  • Fully enclosure guarding
  • Chip conveyor(auger type)
  • Work light
  • Alarm lamp
  • Heat exchanger
  • Remote MPG
  • Coolant system including coolant tank
  • Lubrication system
  • Leveling screws and pads
  • Maintenance tool box
  • Tool tip air blow system
  • Air purge
  • Shower coolant system
  • Extra coolant tank
  • Spindle oil coller(chiller)
  • 6000rpm spindle
  • Spindle oil chiller
  • Two speed gearbox
  • C.T.S preparation
  • Linear scales
  • Tool overload detection
  • Auto tool length measurement
  • Automatic workpiece measurement
  • Simple tool life management
  • Chip conveyor outside machine & chip bucket
  • oil skimmer
  • Coolant gun
  • Rotary table preparation
  • Manual tail stock for rotary table
  • Through hole drill kit
  • Auto counter for work piece
  • DNC link software
  • Arm A.T.C with 24 tools magazine
  • Drum A.T.C with 20 tools magazine
  • Automatic power off
  • Oil coolector
Machine in Action - Video Clip
Enquiry